Hello just making a poll, which one do you prefer? personally I prefer x265 but since the rarbg falldown i’ve seen that almost all 1080p rips are in x264, what do you think about that, and do you recommend any place to find more x265 content beside those in the megathread?

  • BermudaHighball@lemmy.dbzer0.com
    link
    fedilink
    English
    arrow-up
    3
    ·
    1 year ago

    Note that H.264 and H.265 are the video compression standards and x264 and x265 are FOSS video encoding libraries developed by VideoLAN.

  • CCatMan@lemmy.one
    link
    fedilink
    English
    arrow-up
    1
    ·
    1 year ago

    Because of this post, I reencode a BD rip I made using handbrake to see how small the output file would be. I used the 4k av1 fast profile, but changed the audio tract to passthrough. Holy crap, 44gb down to 1.5gb. what black magic is this?

    • maximus@lemmy.sdf.org
      link
      fedilink
      English
      arrow-up
      0
      ·
      edit-2
      1 year ago

      AV1 is very efficient (around twice as good as h264), but a filesize that low was almost definitely because the default encoding settings were more conservative than the ones used to encode the blu-ray. The perceptual quality of that 1.5gb file will be noticeably lower than the 44gb one

      • obviouspornalt@lemmynsfw.com
        link
        fedilink
        English
        arrow-up
        1
        ·
        1 year ago

        I’ve recoded a bunch of x264 to AV1 and routinely gotten file sizes that are 10-15% of the original file size (a little more than 1/10th the original size)

        What I’ve found is that source content often has a lot of key frames. By dropping key frames down to one per 300 or one per 150 frames (one per 10 or 5 seconds for 30fps) and at scene changes, you can save a LOT of space with no loss of quality. You do give up the ability to skip to an arbitrary point in the content, however. You may have to wait a few seconds for rendering to display if you scroll to an arbitrary point in the content.

        If you’re just watching the content straight through, no issues. I set CRF to achieve 96 VMAF and I can’t tell any difference in quality between the content with that setup.

        I had one corpus of content that I reduced from 1.3 TB down to 250 GB after conversion.

        Unfortunately, only the most recent TVs have AV1 playback built in, and the current Fire sticks, Chromecast don’t have support for playback from a LAN source. I’m hoping the next crop of Chromecast and similar devices get full support, I’m assuming it’s just a matter of time until AV1 decoding is included in every hardware decoder since it’s royalyy-free.

  • PeachMan@lemmy.one
    link
    fedilink
    English
    arrow-up
    0
    ·
    1 year ago

    H265 is objectively superior in just about every way UNLESS you’re trying to play it on hardware that doesn’t support it. The only reason to use H264 is for broad compatibility.

    • IceSea@lemmy.world
      link
      fedilink
      English
      arrow-up
      0
      ·
      1 year ago

      also its not just pure “compatibility”, but I had a time when I played vids to my TV over an old laptop (from around 2015). Worked like a charm. But some x265 vids went into full-on stutter mode in scenes where a lot of stuff was happening… was more a nuisance than a dealbreaker, but still, preferred x264 versions if I could get them

      • PeachMan@lemmy.one
        link
        fedilink
        English
        arrow-up
        1
        ·
        1 year ago

        Sounds like your TV isn’t fully compatible with x265. You can get around that by using a modern streaming stick that supports it.

      • PeachMan@lemmy.one
        link
        fedilink
        English
        arrow-up
        1
        ·
        edit-2
        1 year ago

        Pretty sure it’s just more of a hardware age issue. Smart TV makers don’t put much effort into their firmware, so if they don’t support a codec now they probably won’t support it ever. Devices made before a certain year probably won’t ever support H265. I suspect we’ll run into the same thing with AV1, unfortunately. It’s another objectively superior codec that will have compatible issues. 🤷

  • Loki123@pathfinder.social
    link
    fedilink
    English
    arrow-up
    0
    ·
    1 year ago

    I have a personal Jellyfin server, and I usually reencode from x264 to AV1. Though if it’s a matter of choosing a source, I always go for x264 for the least compression.

  • fades@beehaw.org
    link
    fedilink
    English
    arrow-up
    0
    arrow-down
    1
    ·
    edit-2
    1 year ago

    Shit, I like HEVC in theory for the compression especially but it’s copyrighted bullshit or whatever.

    I use Plex with lifetime pass on my QNAP NAS and it has to hardware transcode HEVC to a playable format because of said copyrighted bullshit.

    It doesn’t affect me that much unless I’m trying to jump around on the media as it will need to load. The other thing is that you can have Plex save transcodes but that obviously gobbles up disk space.

    tl;dr 264 = 👑